Advance window introduction

• ReadIO: ASPI/SPTI/LIBC are selectable;
  1.LIBC: Design for reading early DVDs. It reads DVD with Window API; the reading speed is higher than other mode,but can't skip bad sectors.
  2.ASPI: Design for reading latest DVDs which has new copy protection,such as Sony or Disney DVDs. It reads DVD with wnaspi32.dll which would control the DVD drive directly and skip bad sector quickly.
  3.SPTI: It is an alternative of ASPI. It reads DVD with windows SCSI interface,high reading speed and skip bad sectors quickly. The default is ASPI
  
  
  
• skip bad sectors step:
  In order to improve the reading speed, DVD-cloner will skip over some bad sectors automatically in the reading progress. You can set a skipping value 0~10000. The bigger of value is, the faster the reading speed is. But the bigger value may lead to lose more valuable data. If you are not sure whether there are some bad sectors in your DVD or not, please use the default, that is 100.
  
  
  
• Reading Speed:
  Adjust the reading speed. If you set it to "heigh", it will read fast but occupy a lot of system resource. If you set it to "low", it will read slowly but occupy a relatively smaller system resource. Should the computer slow down during the reading process, set a lower reading speed. The default is mid.
  
  
  
• Burning Speed:
  Set the burning speed. Please note that the burning speed should match the DVD R/RW you use. The default is Maximum-- to use the highest speed compatible with the disc.
  
  
  
• Screen ratio:
  Adjust the screen ratio. Except for special need, Auto select is highly recommended. The default is Auto select.
  
  
  
• D5 Disc size:
  Set the size of target D5. Adjusting this value will affect DVD compression rate. Please do not exceed the DVD R/RW's biggest capacity that you bought. The default is 4300M
  
  
  
• special features compress rate:
  When playing a copy that cloned by 'Movie complete copy', if you found the special features pictures is coarse, you can increase the compress rate properly to get better picture effect. But the too high compress rate needs bigger saving space, and finally makes the quality of the main movie decrease.
  The default is 30%
  
  
  
• Temporary directory:
  The temporary directory will be used when setting the copying mode. Pleas note that the temporary directory should be in the NTFS subarea ( in "my computer", right click the disc driver and choose the "properties" to see whether the driver is in the NTFS subarea. The default is to use the disc driver with the largest free space.
  
  
  
• To decode some specially encrypted DVDs, DC has to close the automatic play function of DVD driver. When it needs to close it, a prompt will appear. You can resume or close the automatic play function manually with this switch. Please note that this option will come into effect only after rebooting your computer.
  
  
  
• Remove new sony copy protection
  This option is used to copy the latest SONY movies and also suitable for those with protective bad sectors. Highly recommend you to choose this option. The default setting is in the chosen state.
  
  
  
• Authenticate DVD region when start
  If this item is chosen, free region will automatically begin when starting DVD-CLONER. Please note that free region is necessary before copying. If this item is cancelled, you must use players such as power DVD to play and then start DVD-CLONER to make the backup. Otherwise an error prompt will appear. The default is in the chosen state.
  
  
  
• Check updata automatically every month.
  This aims to keep you informed of the latest DVD CLONER. Having chosen this item, the program will check for the latest version per month. The default is in the chosen state.
  
  
  
• Delete temporary files when finished.
  If this item is chosen, the temporary film file will delete automatically after the copying completes. Please note that no warning prompt will appear during the deletion. The default is in the chose state
  
  
  
• Popup information window when start
  This means to copy under the Export interface. If this item is chosen, click "Start" and the task confirmation window will pop up. The default is in the chosen state.