| Function |
Description |
| Index |
Select the desired program index (PGC).
Most movies are stored in index 0.
Default is : 0 |
| Angel |
Select the desired camera angle.
Most movies are stored in angle 1.
Default is : 1 |
| DeMacroVision: |
Remove macro vision protection from the movie.
Default is : Yes |
Key Search:
|
Mode for CSS key search (the mode 0 works fine in 99% of cases).
0 - Search a key one time when starting
1 - Search a new key at each VOB-ID
2 - Search a new key at each CELL-ID
3 - Search a new key at each VOB/CELL-ID combination
4 - Disabled
Default is : 0 |
| Dolby Surround: |
Enable Dolby Surround downmix.
Allow to preserve better 5.1 FX in stereo mode
Default is: Enabled |
| Audio 48KHz to 44.1 KHz: |
48KHz downsampling mode.
0 : Normal mode (fastest)
1 : High quality (slower)
2 : Export AC3
Export the source AC3 to a file, you can afterward select the output file by clicking on the Select AC3 Output button.
3 : 44.1KHz (no conversion)
Select this when you don't want to make sound conversion when you have a 44.1KHz source stream.
4 : 48.0KHz (no conversion)
Same purpose as choice 3, when the input frequency is not specified (A3,LPCM) it is usually 48KHz
Default is : 0 |
Volume:
|
Gain of the audio output.
No normalization is performed. A value of 1 can't generate distortion (cracking) but the output sound may be very low. The default gives a good volume for most DVDs.
Make few clip of the movie where you know the volume is high and adjust this value in order to get a good volume. You can also use the sound normalizer to find an optimum volume.
Default is : 3 |
| Subtitle Offset: |
Vertical offset in pixel of the subtitle.
This values is automatically adjusted if the subtitle goes out of the screen
Default is : 0 |
Original color:
|
Preserve original color from the IFO file.
Uncheck it if your subtitle looks too much bold
Default is : Yes |
| Overlap: |
Go backward of specified amount of time when output volume size has been reached. (This has no effect in custom chapter splitting) i.e. Overlap=10 if the volume end at 1:10:25 next volume will start at 1:10:15.
Default is : 0 sec |
| Audio Video Synchronization: |
Re-synchronize video and audio periodically. (not always necessary)
Default is : No |
| Luminance filter: |
Allow to adjust light of source.
The Y plane is the luminance plane (in YUV format) Apply Gain*Y + Offset on the Y plane. Gain is 8.8 fixed point value. ( 0 = 0.0 ; 128 = 1.0 ; 256 = 2.0 )
Default is : Not enabled, Gain: 128 , Offset: 0 |
| Output frame rate |
Frame rate of the output video file. 25 (PAL) or 23.97,29.97(NTSC).
Warning: this value is not automatically set, if you choose a different frame rate from the input, a pull down will be performed. Avoid conversion between NTSC and PAL.
Default is : 29.97 |
| Detect 24Fps: |
Detect automatically 24Hz progressive NTSC.
Default is : Yes |
| Force 24Fps: |
Force input to be a 24Hz progressive NTSC.
This flag works only if detect 24fps is checked. (Use it if you think that the 24Hz detection doesn't work).
Default is : No |
| Save your DVD drive: |
Create a temporary buffer to avoid the drive to be switched on/off too much.
If you use a RAM buffer you may disable virtual memory to get more speed. The file will be write in your Windows temporary directory (TMP environment variable).
Default is : Size: 10MB, Location: RAM |
| Deinterlace Filter: |
Use this when your image is interlaced (when 1 line / 2 is shifted)
Warning: if you set odd or even field you cannot be sure that it is the good field, Just make a clip of 10 images to see if you're right. Interpolate mode interpolate the even field (you lose a bit quality for SVCD but it always works)
Default is : None |
